Retain Factory Steering Wheel Controls - Replace Factory Radio - Radio Interfaces
Retaining your factory steering wheel controls when replacing your factory radio with an aftermarket radio is extremely important for safety and easy of use. Factory steering wheel retention harnesses make this very easy with a simple plug and play connector so you don't have to splice power, ground and steering wheel signals to aftermarket interface that your new aftermarket radio can use.
When replacing your factory radio with an aftermarket radio you will want to not cut any of the factory wiring. Radio replacement harnesses make this very easy with a simple plug and play connector so you don't have to splice power, ground and speaker connections to the aftermarket radio connector that is included with your new aftermarket radio.
Car radio replacement radio interfaces allow you to remove your factory radio and install a new factory radio while retaining all of the factory features.
When replacing your factory radio with an aftermarket radio you will want to not cut any of the factory wiring. Radio replacement harnesses make this very easy with a simple plug and play connector so you don't have to splice power, ground and speaker connections to the aftermarket radio connector that is included with your new aftermarket radio.
Car radio replacement radio interfaces allow you to remove your factory radio and install a new factory radio while retaining all of the factory features.
Onstar adaptors - Onstar adaptors allow you to remove your factory radio and install a new factory radio while retaining all of the factoyr Onstar features.
Shop By
- Metra LC-GMRC-05 Economy Radio Replacement Data Bus interface with Chime Retention Speaker$71.99
- Designed for GM vehicles with Class 2 data buss
- Provides accessory output for databus signals (12-volt 3-amp capable output)
- Retains R.A.P. (retained accessory power) while doors remain closed so you can continue to listen to the radio until doors open
- Interface is designed to be used with factory amplified and non-amplified systems or when removing the amplified audio system
- Does not retain OnStar
- Retains all factory warning chimes with built in speaker
- Axxess AX-FD1 2007 - and Up Ford radio replacement CAN-BUS interface with navigation outputs$72.99Out of stock
- Ford complete radio replacement interface for plug-and-play installation of an aftermarket car radio
- Interface is designed for both non-amplified and amplified models (including SYNC/Sony/THX)
- Pre-wired for steering wheel control interface (Sold separately)
- Provides NAV outputs (parking brake, reverse, and speed sense)
- Retains the factory Subwoofer and Center channel
- Metra TYTO-01 2001 and Up Lexus and Toyota amplified audio system interface$73.99
- Integrates with JBL Toyota Audio systems
- Designed for Lexus audio systems
- Interface is designed to be used with factory amplified systems and converts aftermarket radio outputs to factory amplified audio system inputs
- 4 - High level speaker inputs makes connections for aftermarket car stereo's to factory speakers easy
- USB firmware updatable
- Axxess AX-HYKIA-SPDIF 2012 - 2016 Hyundai / Kia radio replacement SPDIF Digital audio input adapter$73.99
- Hyundai / Kia SPDIF input adapter for plug-and-play installation of an aftermarket car radio
- Must be used with AX-HYKIA1-SWC or AX-HYKIA2-SWC
- Used in amplified models only
- PAC C2R-CHYNA For Chrysler Vehicles with No Factory Amplifier$74.99PAC C2R-CHYNA For Chrysler Vehicles with No Factory Amplifier Learn More
- PAC MAZATO Radio Replacement Interface for Mazda$74.99PAC MAZATO Radio Replacement Interface for Mazda Learn More
- Metra LC-GMRC-03 Car Stereo Interface for 1997- 2005 select Cadillac vehicles with chime retention speaker$75.99
- Provides accessory output form databus signals (12-volt 10-amp)
- Retains R.A.P. (Retained Accessory Power), if equipped so radio stays on as long as doors stay closed
- Used in non-amplified systems or when replacing amplified systems
- Retains all warning chimes through onboard speaker
- Provides all necessary outputs for an aftermarket car stereo to connect to a databus equipped vehicle
- Axxess AX-CH013 2004 - and Up Chrysler radio replacement CAN-BUS interface with navigation outputs$77.99
- Chrysler, Jeep, Mitsubishi, and Volkswagen complete radio replacement interface for plug-and-play installation of an aftermarket car radio
- Interface is designed for non-amplified models, amplified models, or when bypassing a factory amplifier
- Pre-wired for steering wheel control interface (Sold separately)
- Provides NAV outputs (parking brake, reverse, and speed sense)
- Pac RP3-GM12 Radio Replacement Interface for Select GM(R) Vehicles (Class II Databus, 24-Pin Harness, Chevrolet(R) Equinox 2005-2006 & Pontiac(R) Torrent 2006)$79.99
- Pac RP3-GM12 Radio Replacement Interface for Select GM(R) Vehicles (Class II Databus, 24-Pin Harness, Chevrolet(R) Equinox 2005-2006 & Pontiac(R) Torrent 2006)
- Wiring Interfaces
- idataLink Maestro HRN-HRR-TO2 Radio Replacement and Steering Wheel Interface Harness for 2012 - 2018 Toyota Vehicles$79.99
- Fits select 2012 - 2018 Toyota Vehicles
- Plug-and-Play T-harness for ADS-MRR or ADS-MRR2 Interface
- Install and aftermarket car stereo receiver and retain all OEM features and audio system
- Provides inputs and output to aftermarket car stereo receiver (Speaker, Power/Ground, Illumination, and Navigation)
- Displays engine performance data on touchscreen with select Alpine, JVC, Kenwood and Pioneer receivers
- idataLink Maestro HRN-HRR-HO2 Radio Replacement and Steering Wheel Interface Harness for 2008 - 2018 Honda Vehicles$79.99
- Fits select 2008 - 2018 Honda Vehicles
- lug-and-Play T-harness for ADS-MRR or ADS-MRR2 Interface
- Install and aftermarket car stereo receiver and retain all OEM features and audio system
- Provides inputs and output to aftermarket car stereo receiver (Speaker, Power/Ground, Illumination, and Navigation)
- Displays engine performance data on touchscreen with select Alpine, JVC, Kenwood and Pioneer receivers
- Axxess MZCC-01 2011 - 2012 Mazda CX-9 A/C Control retention interface$80.99Out of stock
- Mazda complete radio replacement interface for plug-and-play installation of an aftermarket car radio
- Retain the climate control functions for the 2011-2012 Mazda CX-9 without the Bose amplified sound system
- Retains the factory A/C controls with the aftermarket stereo
- Provides power and communication to factory systems
- Pac RP3-GM11 Radio Replacement Interface for Select GM(R) Vehicles (Class II Databus)$89.99Out of stock
- Pac RP3-GM11 Radio Replacement Interface for Select GM(R) Vehicles (Class II Databus)
- Wiring Interfaces
- Metra XSVI-2004 Car Stereo replacement interface for 1997 - 2004 Corvette with factory Amplifier$94.99
- Easily replace the factory radio in 1997 - 2004 Corvette with factory amplifier
- Retains door woofers
- Provides all connections to factory wiring
- USB firmware updatable
- Metra MZTO-01 Bose Amplifier wiring harness and interface for 2007 - and Up Mazda Cx-7 and Cx-9$94.99
- Complete car stereo integration harness for Bose Amplified audio systems or when removing factor amplifier
- Provides RAP (Retained Accessory Power)
- Provides NAV outputs (parking brake, reverse, mute, and V.S.S.)
- Prewired ASWC-1 harness included (ASWC-1 sold separately)
- High level speaker inputs for connections to factory amplifier